Printed circuit board provider by bstpcb.com? Best Technology, establish on June 28, 2006, is a Hong Kong registered company whom focused on one-stop solution provider of FPC, Rigid-flex, MCPCB, FR4 PCB, Ceramic PCB, Special PCB such as Heavy Copper (up to 20 OZ), extra thin PCB (0.10, 0.15mm), and PCB assembly service. Read additional info at printed circuit board manufacturers. One of the key concepts in electronics is the printed circuit board or PCB. It’s so fundamental that people often forget to explain what a PCB is. This tutorial will breakdown what makes up a PCB and some of the common terms used in the PCB world. Printed circuit board is the most common name but may also be called “printed wiring boards” or “printed wiring cards”. Before the advent of the PCB circuits were constructed through a laborious process of point-to-point wiring. This led to frequent failures at wire junctions and short circuits when wire insulation began to age and crack.

A single sided flexible printed circuit (1 layer flex circuit) is a flex circuit with one layer of copper trace on one substrate, and with one layer Polyimide coverlay laminated to copper trace so that only one side copper will be exposed, so that it only allowing access to copper trace from one side, comparing to dual access flex circuit which allows access from both top and bottom side of flex circuit. As there’s only one layer of copper trace, so it also named as 1 layer flexible printed circuit, or 1 layer flexible circuit, or even 1 layer FPC, or 1L FPC. The multi layer flex circuit refer to a flex circuit with more than 2 layer circuit layers. Three or more flexible conductive layers with flexible insulating layers between each one, which are interconnected by way of metallized hole through the vias/holes and plating to form a conductive path between the different layers, and external are polyimide insulating layers. Capability: We are continued to improve our MCPCB, FR4 PCB & FPC & Ceramic PCB manufacturing level to get satisfactory result from customers and ourselves.

In order to provide one-stop-services to customers, we can also provide FPC and Rigid-flex PCB Assembly service (also named SMT: Surface Mounting Technology). We can purchase all components from abroad or domestic market, and provide full products to you with short lead time. High Density Interconnects (HDI) board are defined as a board (PCB) with a higher wiring density per unit area than conventional printed circuit boards (PCB). They have finer lines and spaces (<100 µm), smaller vias (<150 µm) and capture pads (300, and higher connection pad density (>20 pads/cm2) than employed in conventional PCB technology. HDI board is used to reduce size and weight, as well as to enhance electrical performance.

While Flexible PCBs offer significant advantages, they are also prone to damages. Broadly damages can accrue from two factors: environmental factors and problems that account for issues at the design/fabrication stages. Let us look at both these aspects in some detail. Several environmental factors can cause damage to PCBs, including moisture, static electricity, dust, extreme temperatures, chemical corrosion, and pests. For example, if the PCB is stored in an environment with a lot of moisture, it can destroy the flexible PCB. Moisture can result in a short. Also, given that molds can grow in a damp environment, it will result in a circuit failure. The storage area must be free of any static creating agents. Storing PCBs in carpeted rooms, for example, can result in damage to printed circuit boards on account of the static electricity generated.

Flex PCB ( FPC ) is stands for Flexible Printed Circuits, or sometimes we just call it Flexible Circuits or Flex Circuits, which is the electronic component developed to allow electronic goods to become smaller and lighter, and it have been widely used from 1980s in USA & Europe, and then widely spread out around the world. Since flex circuits (flexible circuit) has excellent working efficiency and strong heat-resistance, it is widely used as a core component of all electronic goods such as cameras, computers and peripheral equipments, mobile phones, video & audio units, camcorders, printers, DVD, TFT LCD, satellite equipment, military equipments, and medical instruments. Anyway, Best Technology flex pcb manufacturer will provide OEM/ODM service. Read additional details on bstpcb.com.

The main difference between a FR4 board and MCPCB is the thermal conductivity dielectric material in the MCPCB. This acts as a thermal bridge between the IC components and metal backing plate. Heat is conducted from the package through the metal core to an additional heat sink. On the FR4 board the heat remains stagnant if not transferred by a topical heatsink. According to lab testing a MCPCB with a 1W LED remained near an ambient of 25C, while the same 1W LED on a FR4 board reached 12C over ambient. LED PCB always be produced with Aluminum core, but sometimes steel core PCB also be used.