Top o rings manufacturer: A mechanical seal is a very effective device. Every centrifugal pump must accommodate a spinning shaft while mechanically maintaining fluid or gas contained in the “wet end” of the pump. Mechanical seals consists primarily of a rotary seal face with a driving mechanism which rotates at the same speed as the pump shaft, a stationary seal face which mates with the rotary and is retained using a gland or in some pump models an integral stuffing box cover, a tension assembly (utillizing springs or a metal bellows) keeps the rotary face firmly positioned against the stationary face preventing, excluding, and containing contamination and leakage, both when the pump is not in operation and when the pump shaft is rotating. Static sealing gaskets, orings or elastomeric bellows are strategically located to complete the seal assembly. Find additional details at spring seals.

Before examining how mechanical seals function it is important to understand other methods of forming this seal. One such method still widely used is Gland Packing. Gland packing is a braided, rope like material that is packed around the shaft – physically stuffing the gap between the shaft and the pump housing. Gland packing is still commonly used in many applications, however increasingly users are adopting mechanical seals for the following reasons; The friction of the shaft rotating wears away at the packing over time, which leads to increased leakage until the packing is adjusted or re-packed. The friction of the shaft also means that packing also needs to be flushed with large volumes of water in order to keep it cool. Packing needs to press against the shaft in order to reduce leakage – this means that the pump needs more drive power to turn the shaft, wasting energy. Because packing needs to contact the shaft it will eventually wear a groove into it, which can be costly to repair or replace.

Sealing performance over conventional O-rings is achieved by reducing particle generation, extending seal life and minimizing replacement time during preventive maintenance. Compared to traditional O-rings, this seal effectively reduces the number of dust particles generated during operation and extends the life of the machine with bonded seals installed. The seal has a working diameter range of 6.5 to 60.58mm.

Scraper seals are also known as wiper seals. The scraper sealof DMS SEALS can effectively prevent various forms of contamination that cause a hydraulic system failure. It can be mounted on the outside of the piston rod seal of the hydraulic cylinder to protect the hydraulic cylinder from dirt, dust and moisture. It can well protect the hydraulic cylinder from environmental pollution and effectively prevent damage to the hydraulic cylinder parts, causing the system to malfunction. DMS offers a wide range of wiper seals for different hydraulic systems with different characteristics, specifications and combinations.

The selection principle of the gasket: according to the working pressure, working temperature, the corrosiveness of the sealing medium and the form of the sealing surface. Temperature influence: In normal temperature and low pressure, use non-metallic soft honey gasket; in medium pressure and high temperature, choose metal and non-metal combination gasket or metal gasket; when temperature and pressure fluctuate greatly, choose good elasticity or self-tightening type Gaskets; in low temperature, corrosive media or vacuum conditions, gaskets with special properties should be considered.

Support and positioning The piston and piston rod are radially supported and positioned in the cylinder barrel. Isolate the two pairs of motion pairs of piston and cylinder, piston rod and guide sleeve to prevent direct scratches, abrasions and strains between the motion pairs. Especially when the motion pairs are all steel parts, they must be isolated, otherwise they will be easily strained. The guide belt also has an important role to reduce the friction and friction work between the moving parts, reduce the ineffective work and heat. Vibration absorption and noise reduction Reduce system vibration and noise. It is mainly filled with tetrafluoroethylene and phenolic cloth, and there are also a very small amount of polyoxymethylene, nylon and soft metal. See extra information on dmsseals.com.

DMS Custom Rubber Rings, O Ring Company & factory covers an area of more than 10,000 square meters and the factory area is 8,000 square meters. Our production equipment and test equipment are at the leading level in the industry. We are one of the largest companies in China specializing in the production and development of seals. We have long-term communication and cooperation with many universities and research institutions at home and abroad.

Select the appropriate sealing material: There are many types of sealing materials, including many metals, plastics and rubbers. The same material has different performances from different companies. On the other hand, the same seal has different performances in different working conditions or different sealing schemes, so it must be carefully considered when choosing. Note: Be sure to consider seals under the premise of a reasonable sealing scheme, then consider the sealing material, and then consider the seal manufacturer. If you don’t have enough sealing experience, it is best to consider the sealing company first, and let the sealing company consider the sealing scheme and other issues, such as DMS Seals Technology Co.,Limited.

The radial force of our rotary seals on the shaft and the distribution is very reasonable. It can achieve the optimal “critical oil film thickness” working condition and always maintain critical lubrication. We guarantee that our rotary seal can help the machine get the sharpest “peak” pressure distribution with the least radial force, providing the best sealing effect. The bearing seal is designed by DMS SEALS to isolate the moving metal part, guiding the piston and piston rod of the hydraulic cylinder to move in a certain direction and it can help withstand lateral loads. It helps prevent any direct contact between the piston metal and the cylinder metal and prevents strain and seal damage on the inner surface of the cylinder.