The best paintless dent repair (PDR) in Colorado: This technique is popular among automotive enthusiasts when it comes to the removal of small dents. The idea is simple: heat will inevitably cause the metal surface to expand and (hopefully) pop the dent out. Remember that the more time the car spends time under the sun, the better this technique will work. Use a plastic and/or leather conditioner for the car’s interior, so as to not damage it while exposing the car to maximum sunlight. If the sun’s heat isn’t particularly strong that day, a simple hair dryer could be used in conjunction with the sun to concentrate the heat to a specific area. Point the hair dryer to the dented area for two-minute intervals until the dent pops out. Be careful not to touch the hot lip of the hair dryer on any painted surface. A two-to-four inch gap between the dryer and the surface is recommended.

In the first place let’s begin with some car paint care tricks: Applying dry ice to the dent is an effective way for fixing hail damage. The huge change in temperature can force the dents to pop out. Everything for you to do is just moving the dry ice around the damaged area to cool the area rapidly. But be careful as dry ice will damage your skin if you don’t wear gloves when handling it. Fixing hail damage by dry ice can be a cool solution, but sometimes it can not remove all of the dents. So in this case, you will need to do additional repairs.

If you want to polish your car and are considering buying a buffer, you can see my simplified approach to car polishing for the true beginner to achieve professional results. As the saying goes, “an ounce of prevention is worth a pound of cure”, and your car is no different. If you are just consistent with the basic instructions I have provided here, your car will not only look fabulous year after year, but will retain much more of its original value when you are ready to sell. Want to save your time and maximize your car detailing efforts. Unless you are a die hard car enthusiast, I actually recommend you find a quality, 100% cloth or hand wash, and take your car there at least every 2 weeks and let the crew there perform the grunt work of car washing.

Apply the dry ice as many times as you need to, but it should pop out eventually if the dent isn’t too deep. You can also try heating up the dent first, with something like a hair dryer (similar to the hairdryer and compressed air tip above), and then apply the dry ice to it. Suction is one way to get out a dent, but the problem is finding a dent puller with the right amount of power. Well, why not just create your own? All you need is a pot (or bucket), a vacuum cleaner and some tape and you can get that dent out of your car in no time.

Paint Conditioner. If you’ve recently painted your vehicle or purchased a new vehicle, consider using a non abrasive paint conditioner to protect the paint. Non abrasive conditioners have to be sprayed on, in small amounts. Follow the instructions listed on the package to get good results. If you want to re-paint an old vehicle to maintain the exteriors, make sure you research the best new car paints available in the market. You need to also carefully follow car paint preparation techniques to do a good job. See more details at evidentpdr.com.

PDR is a specialized form of autobody repair where technicians use special tools and techniques to slowly reduce a dent down in size until it completely disappears. PDR is a learned skill. Through trial and error, technicians gradually begin to understand the specific areas of a dent to manipulate, exactly how to manipulate certain locations of a dent, and the specialized processes and technologies used to remove a dent without the need to repaint the area.

So, we’ve explained what the procedure looks like — assuming it was done properly. And as you could probably guess there are a lot of ways an amateur or first-timer can get it wrong. It’s different than most other car repairs because it’s not about mechanical prowess; it’s more about control and the ability to maintain a steady hand and a gentle pace. You can’t rush it. The problem is, once a sheet metal repair starts to go awry, you’re usually much, much worse off than if you’d just left it alone. Metal holds its shape, but only to a certain point. Let’s say you get a dent in the hood — nothing too drastic, just a shallow, even dent with no sharp creases in an area that’s pretty easy to reach. You think it’ll be easy to pop it out on your own, so you begin to massage the underside while holding your shaping tool in place. You’ve made good progress so far, and a casual observer wouldn’t even notice the flawed area. But it’s not exactly perfect, and since it’s been fairly easy to this point, you decide to keep massaging the area to make it flawless. After a few more minutes of massaging, you realize that you’ve pushed it just a little too far. And now you’ve got this flabby area on the hood where you stretched out the metal. And there’s no easy way to shrink it back down. Keep going and it’ll stretch even more. Lesson learned.