Cutting discs shop Ireland today? In many shops, the operator has to go to a tool room or supply area for a new contact tip, coil of wire or other welding accessory. This takes valuable time away from the welding cell and slows down overall productivity. To improve the operating efficiency and minimize wasted time, companies should stock at least a limited supply of all necessary items near the welding station – this includes shielding gas, flux and wire. Another helpful productivity enhancing tip is to switch to larger spools of wire such as from 25 lb. spools to 44 or 60 lb. spools to even larger packages of 1,000 lb. reels or 1,000 lb. drums. A simple switch like this means less changeover time, which adds up over the weeks, months and years. Shops should also be on the lookout for shielding gas waste. A simple device called a surge turbine can be placed at the end of the gun to provide a digital readout of the gas surge and flow rate. If the surge rate is high, investing in a surge guard can reduce the pressure, eliminating gas surges and waste. Leaks in the gas delivery system can also create a potential loss of money. By looking at the amount of consumables purchased each year and then examining the total gas purchased, a company can determine if there is a significant loss. Welding manufacturers and distributors should be able to provide average utilization figures so that loss can be detected. If there is a loss suspected, one of the easiest ways to check for leaks is to shut off the gas delivery system over the weekend. Check the level on Friday evening and then again on Monday morning to determine if gas was used while the system was in shut down mode. Discover extra info at welding supplies.

How to pick a welder tips: Stepped voltage or synergic: Synergic MIG’s have the edge when you’re welding stainless & aluminium as they are pre-programmed, easy to set up & portable. They also provide a better weld characteristic and so give cleaner weld bead with less/no spatter. Inverters: Considerably smaller and lighter and so ideal for site work. All inverters are stepless and so have infinite control. Also cheaper to run power wise. Budget: How much welding are you going to undertake? Gear your purchasing decision around the jobs you will be working on the most. Polarity changeover; A lot of welders at the light industrial end will to be able weld with gasless flux cored MIG wire. Is the switchover easy on the machine you’re considering. Availability of spares & after sales service: Ask where the machine is actually made. Even the more recognised brands largely outsource their production, which can lead to quality and after sales issues with lack of continuity of supply for spares.

The duty cycle is the amount of time the welder can run continuously before needing to cool down. It’s expressed as the percentage of 10 minutes the MIG welder can run. So a 20 percent duty cycle at 90 amps would mean that when you’re welding at a 90 amp rating, you can go continuously for 2 minutes before the welder needs to cool off for 8 minutes. That means if your 140-amp welder is rated for 20 percent at 90 amps, it’s probably only able to weld for less than a minute at the full 140 amps. How Much Power Do You Need? This is the single factor that affects the cost of MIG welders. Newer 120 volt machines are able to run up to 140 amps, good enough for ?-inch steel. However, at that rating, the duty cycle will be fairly short. That’s not a big concern for home hobbyists and weekend warriors, but it will really put a cramp in your style if you’re doing production welding. Dual-voltage machines are now beginning to provide a lot of control, at least on the 240 side, but unless you’re buying big-name stuff that can get pricey, it’s likely the 120 side won’t provide the same quality of welds.

Some tips about welding equipment, MIG and TIG welders, plasma cutters. MIG Welders are extremely popular because they tend to cost less than TIG or Stick welders with comparable power and features, are extremely easy to learn, and can tackle a wide variety of projects. Since the filler metal is fed through the MIG welding torch, welders can use both hands to hold the torch steady rather than using one hand to add filler metal, as in TIG welding. The wire feeder also makes MIG welding up to four times faster. The MIG welding process uses an inert gas to shield the weld and to keep it free from impurities. This makes MIG welding very neat and easy to clean up since there isn’t anything to chip away, which is typical for Stick welding. MIG welding can be used on a wide variety of materials such as aluminum and is also frequently used for automotive work. However, MIG also requires the purchase of shielding gas and generally requires materials that cost more when compared to other methods.

Additionally, like in any kind of arc welding, if you’re handling projects that are going to produce high heat and take a long time to finish, then you’ll need a welder with an internal cooling system to help you to avoid any issues with over-heating. To find out exactly how long your welder can run for, look at its duty cycle. As a general rule of thumb, a cheaper machine will often have a shorter duty cycle, which means that they’re not well-suited to welding thicker metals. There are man welding metalplenty of additional issues to consider when choosing your MIG welder. For instance, you might want to make sure that maintaining and repairing your new device is simple, particularly if you plan on using the welder for work or professional purposes. Read more info on https://www.weldingsuppliesdirect.ie/.

The sort of build quality that you’d expect from Makita. This angle grinder is tough, well put together and built to take a beating. Makita have included a lock-off power switch. I’m a big fan of these compared to the “deadman” style switch you need to hold to keep the disc spinning. They can tire your hand out quickly and aren’t ideal for long grinding sessions. You get a 2.5m power cable to play with. It’s long enough for most grinding jobs, and the quality of the power cord is excellent as well. Makita use labyrinth rings to seal the bearings against dust. Anyone who uses angle grinders a lot know how much dust they produce, so this is a welcome feature. Attaching the side handle can be a bit of a pain. You’ll need a long screwdriver to hold the bolt in place inside the handle. Compared to simple screw-in handle on the Bosch GWS 7-115, this one can be tricky.

The Lincoln X-Tractor Mini weld fume extractor has a 99.7% efficiency in removing welding fumes. It’s adequate for keeping your house or store fresh. 80 dBA sounds that it generates are close to nothing comparing with other fume extractors. Despite being a mini portable fume extractor, the X-Tractor Mini has versatile usability. It can be used for flux-cored welding, MIG and TIG welding, and stick welding. This portable weld fume extractor from PACE is ideal for benchtop soldering and electronic rework. The low-cost Arm-Evac 150 System includes everything you’d find in the best portable welding fume extractor. 3-stage filtration system adds immense value to its overall efficiency.

If value for money is a priority to you, take a look at this drill from Evolution. It is a solid and durable drill that will get the job done for the professional steelworker as well as the weekend handyman. This drill has a 6-inch stroke length and comes with a 0.5-inch chuck and key. The drilling range has a diameter from 7/16? to 1-1/8? and cutting depth of 2 inches unless you change out the chuck to something else. You can place the feeding handle on either side of the drill, depending on what is comfortable to you. The heavy-duty magnet makes it easy to do overhead or horizontal drilling. An integrated cooling system will keep your magnetic drill press from overheating. There are some drawbacks to this drill. It can only turn at the speed of 570 RPM. This works great for when you are drilling steel or aluminum, but this speed is too high for drilling titanium or stainless steel. This drill may also be more primitive than conventional high-end magnetic drill presses.

ESAB is a world leader in the production of welding and cutting equipment and consumables. Our innovative, world-renowned equipment and solutions are developed with input from our customers and built with the expertise and heritage of a global manufacturing leader. For each discipline, continuous development of methods, materials and know-how is being directed to meet the challenges posed by the diversity of industry sectors we serve. ESAB is organized to deliver efficient, high-productivity solutions to meet customer requirements in a manner that exceeds their expectations no matter the market segment. Continuous Improvement (Kaizen) Is Our Way Of Life – Set breakthrough objectives, experiment and learn every day, eliminate waste in our business processes, and benchmark the best, then better them. Living this value is done through understating that Change is a Must, and the use of Tools for Improvement. To live this value each ESAB associate fosters an environment of continuous learning employing the Colfax Business System Tools which is the basis of our culture.

Our welding tables are to be self-assembled. This is an easy process; full instructions are provided. A wide range of tools are available for use with these tables and they are available as added optional extras in the custom options above. If you require guidance on which tool set would be the most suitable for you please feel free to call our helpful staff. *Please note that current lead times on these welding tables are 3-4 weeks, however if you require the table quicker please alert us and we will do our best to assist with your enquiry*

The Hobart Handler 140 is an excellent choice for beginner welders, which is why it’s probably the most popular welder on the market. This thing is solidly built and is a step above many of the other 140A welders. The arc runs smooth and produces great results. It’s suitable for a range of general repair tasks and projects like trailer frames, autobody repair and anything up to 1/4 inch thick. If you’re just getting into welding, you can’t go wrong with this little machine! What’s better is that it’s an absolute steal at under $500. See the full review here.

The MIG welder performance depends on several parameters. The duty cycle is among them. It means the percentage of a 10-minute period the welder can work until it gets overheated. For example, “90A / 20%” means that a welder can work for 2 minutes at 90A before an 8-minute cooldown, i.e. 20% of 10 minutes. Now, about the material. We should note that the maximum thickness of a material a welder can handle depends on its amperage and welding wire thickness. Lastly, consider the thickness of the joint a welder can make in a single run. Household models can weld metal sheets from 18-gauge to 1/4” thick at the output of 70A – 180A, respectively.

UK market choice: Compared to the Hobart 500559 Handler 140amp MIG welder above, the MVP is a more powerful, dual voltage MIG welder for beginners. Its heavier and about $300 more to buy, but the thicknesses it can weld are greatly increased. It has several power outputs to choose from. The bottom line is that the MVP is worth buying if you need more power than the Handler 140 can offer. For beginners and pros alike, the MVP lives up to its name. This is a dual voltage machine that can weld from 24 gauge to 3/8 inches of steel. Among the metals, it can weld are steel, stainless steel, and aluminum. The MVP has 7 power settings to choose from. The spool hub can handle both 4 inch and 8 inch reels.

Use the Personal Protective Equipment (PPE): It is mandatory to use various appropriate PPE while handling an industrial gas cylinder. For instance, wear safety glasses, safety shoes, gas masks, and safety glasses, while working with cylinders filled with compressed gases. Similarly, it is important to use flame arrestors when using acetylene cylinders in compressed air. Use Regulators Properly While Handling Cylinders: Regulators are devices, which are designed to lower the working pressure of the gas. These devices differ according to gases. Many times, the regulators aren’t handled and stored properly. This improper usage may lead to problems in the long run. Hence, it is important to take several precautions while using regulators.

The S SATC PCS Metal Cutting Disc for Angle Grinder is made with a proprietary aluminum oxide grain combination that creates an aggressive cutting action. This allows the user to cut through materials more easily. In addition, the wheel also has a balanced Cut Life, Cut Rate, Cut Precision, Power Demands & Heat Buildup. This means that you can cut through materials for longer periods of time without having to worry about the accuracy of the cut or the heat that is being generated. The SATC PCS Metal Cutting Discs will cut through most surfaces with ease and do not slow down as they work like other standard discs. These new discs also last much longer than other brands which allows you to make even more cuts before needing a replacement disc.